News

Sodick “Goes Large” with all the latest technology at MACH 2020 – STAND 20-310

Sodick Europe, together with sole UK distributor Sodi-Tech EDM, is all set to “go large” at MACH this year, with its biggest-ever stand at the exhibition. Examples of the latest Sodick technology across a range of machining and production processes will be at the show, not only wire and sink EDM, but also high speed milling as well as horizontal injection moulding.
Seen for the first time anywhere, will be a prototype of the new 5-axis K4HL small hole drilling machine, developed specifically to meet the requirements of the aerospace industry to drill thousands of high precision holes in exotic materials for jet engine turbines.

UH650L – high speed milling

Sodick’s new generation of high-speed machining centres incorporates linear drives in all axes. And, unlike conventional machines, the UH650L combines both rough and fine milling in one operating mode, with a rapidly rotating and traversing tool of small diameter that cuts to fine depths – resulting in enhanced dimensional accuracy, surface finish, and tool life.

High-speed milling shortens cycle times and therefore the whole machining period. Other advantages are improved surface quality, multi-purpose tools, and minimising chip sizes for ease of disposal. Furthermore, this technology does not require coolant and mist machining is also possible.

Wire EDM – the best gets better

For customers looking to take wire EDM accuracy to a new level, the super-accurate ALC400P is the answer – every element of the AL-P series has been developed to satisfy the most demanding requirements, for example a pitch accuracy of +/-1 micron.
ALC-P machines incorporate as standard an inverter-type dielectric chiller which monitors and maintains the dielectric temperature to within +/-1 degree, minimising the thermal effect inside the work-area. An additional thermal sensor is installed inside the work-tank for even more accurate temperature control. Even the door to the machine has been considered and is constructed of carbon fibre to minimize “weight shift”.
The VL600Q, part of Sodick’s VL series range of advanced performance wire EDMs, builds on the technologies of the AL series. The large capacity VL600Q is well-suited for a wide range of machining applications and incorporates advanced tension servo control, precision pick-up function, an energy saving circuit and a dielectric cooling unit. Options include a rotary table, a large wire spool feeder and a PCD tool cutting package.

Sodick Die Sinking – going from strength to strength

The AD35L demonstrates Sodick’s dedication to innovation, using 3D design systems and the latest CAE technologies, numerous simulations have made it possible to create an improved basic machine structure with increased rigidity, to minimise deformation and enable optimum performance at high-speed and rapid-acceleration linear motors. Furthermore the design of an independent X and Y-axis, plus an efficient machine layout, leads to a longer stroke, smaller footprint and highly accurate machining capability.
The AG60L really requires no introduction, as the best selling model in Sodick’s AG range it provides high speed, high accuracy cutting, incorporating linear drive technology and simplified control mechanisms, while providing a direct link between the drive and control and ensuring the fastest possible servo response and optimal spark gaps at all times.

Injection Moulding – GL30-LP

Last, but by no means least, Sodick’s new horizontal injection moulding machine is making its MACH debut. Although the machine has already been seen in Europe, it is expected to raise considerable interest at the NEC.
Sodick’s GL30-LP moulding machine incorporates a two-stage plunger injection system, the V-LINE®, which is designed to provide three critical capabilities: a consistent plasticizing heat profile, a constant filling volume and constant holding pressure – together these capabilities ensure that the machine achieves ultra-precision injection moulding, consistently and reliably.

Issued by:
SMPR Limited, Dovecote Cottage, Manor Court, Stretton on Fosse, GL56 9SB
Contact: Shelagh Morgan, Tel: 01608.663425, e-mail:info@smpr.co.uk

On behalf of:
Sodick Europe Ltd., Agincourt Road, Warwick, Warwickshire, CV34 6XZ, UK
Contact: Manabu Takemura, 01926 698888, email: europe@sodick.eu.com, www.sodick.org/

All News

Sodick “Goes Large” with all the latest technology at MACH 2020 – STAND 20-310

Sodick Europe, together with sole UK distributor Sodi-Tech EDM, is all set to “go large” at MACH this year, with its biggest-ever stand at the exhibition. Examples of the latest Sodick technology across a range of machining and production processes will be at the show, not only wire and sink EDM, but also high speed milling as well as horizontal injection moulding.
Seen for the first time anywhere, will be a prototype of the new 5-axis K4HL small hole drilling machine, developed specifically to meet the requirements of the aerospace industry to drill thousands of high precision holes in exotic materials for jet engine turbines.

Read more …

RST Engineering doubles-up on Sodick AG60L die-sink EDM machines

Following a recent move to a facility more than twice the size of its previous premises, RST Engineering has invested in another Sodick AG60L die-sink EDM to help keep pace with a growing order book. Installed in February 2018 by Sodi-Tech EDM, the machine joins an existing AG60L that has performed impressively since 2012. The two machines are now working side-by-side producing a host of complex parts such as titanium internal gears and splines for the motorsport industry.

Read more …

Sodick wire EDM provides 50% speed boost at rapid manufacturing specialist

Laser Prototypes Europe (LPE) is one of the UK and Ireland’s longest-standing specialists in rapid prototyping and rapid manufacturing for a plethora of industries. Among its many services is DMLS (direct metal laser sintering) – the 3D printing of metal parts. The ability to print components with complex geometries in short cycle times is a huge competitve advantage for LPE and its customers. The DMLS process requires a lot of heat and energy to sinter the powder, which creates in-built stresses that can lead to distortion of the part. To counter this effect, heatsinks and anchors must be added to the component. After 3D printing, wire EDM is used as a finishing process to remove these and achieve final tolerance. Here, LPE has just added a second machine to its portfolio, a VL600QH from Sodi-Tech EDM, which is performing duties some 50% faster than the existing Sodick machine installed in 2017.

Read more …

EMO 2019 impressions

EMO 2019 in Hannover was a great show for the Sodick team. Around 117,000 experts from all over the world visited the world's leading trade fair for metalworking, where we were delighted to present our innovations and classics again.

Read more …

Sodick Brings Best-of-Breed EDM, Milling and Injection Moulding to EMO

With its largest ever stand at EMO, Sodick is once again bringing best-of-breed technology to the exhibition, with European debuts for the ACL400P super-high accuracy wire EDM, the ALC800G large capacity premium wire machine, the new UH650L high-speed milling machine and the MS100 plastic injection moulding machine. 

These newcomers are accompanied on the stand by two of Sodick’s most advanced EDM “big beasts”, the AG80L die sink and the ALC800G wire machine, while automation options are being demonstrated by the AG60L die sinker with robot and the OPM250L additive manufacturing machine.

Read more …

High-speed milling

Additive Manufacturing

Hole Drilling EDM

Injection Moulding Machines